Excerpt from the latest article published in DC Velocity:
"Two product categories that haven't changed much in the last 10 years—batteries and chargers for lift trucks and mobile devices—are undergoing a transformation.
If you've been operating under the assumption that the batteries and chargers you will use to power your forklifts and mobile devices a few years from now will be pretty much the same as the ones you've used for the past decade, you'd better sit down. We have news for you: This normally staid product category is on the verge of a revolution.
Advances in technology are fostering a wave of innovation in chargers and batteries—both very large ones, such as those for electric lift trucks, and very small ones for mobile devices like bar-code scanners, RFID readers, and printers. There's a lot going on, and we can't cover every recent development in this short article. (We've left out lithium-ion batteries for forklifts, which we covered in a separate article last year, for example.) But we can offer a few examples of the capabilities that are turning old-school equipment into 21st century tools. Here are five that bear watching:
1. Alerting users to problems as they happen. Electronic monitors and diagnostics for forklift battery utilization, power usage and output, and water levels have been around for a few years. Earlier generations required technicians to connect the batteries to a computer or testing device during troubleshooting or scheduled maintenance. Now, thanks to wireless communication, it's possible to transmit data in real time, alerting fleet managers when a problem first develops, not days or weeks after the fact.
These wireless battery monitoring systems continuously collect, log, and report information like temperature, water levels, charge intervals, and state of charge while the battery is operating. If a problem develops, they send an alert via e-mail or text message. This information is also delivered to an online portal or cloud-based software platform, where it can be analyzed and managed, allowing fleets to compare batteries' performance by truck, individual site, or a network of sites. Some examples on the forklift OEM side are Raymond's iBattery, Crown Equipment Corp.'s Battery Health Monitor, Hyster Co.'s Hyster Battery Tracker, and Yale Materials Handling Corp.'s Yale Battery Vision products. Examples from independent providers include Advanced Charging Technologies' (ACT) Quantum and Power Designers USA's PowerCharge.NET comprehensive solutions, both of which monitor, report on, and manage batteries as well as chargers. (Many other products on the market monitor battery performance remotely; most track a more limited range of functions.)
2. Monitoring beyond the battery itself. Traditionally, exterior parts and components that aren't part of the forklift battery itself have been monitored by visual checks and physical tests during scheduled maintenance. Now, we're starting to see ongoing monitoring and remote data collection for such items.
One example is charge cables, which can suffer wear and tear while the lift truck is in use and from being plugged and unplugged repeatedly. Waiting for scheduled maintenance can be risky. "If they are not properly maintained, cables can suffer damage and even melt, which can affect the trucks and the goods, and most importantly, the safety of the driver," notes Jonah Teeter-Balin, director of product marketing for AeroVironment. To prevent such incidents, AeroVironment developed Connect RX for its PosiCharge ProCore chargers. This technology monitors cable connectors during charging sessions, shutting down the charge session and alerting the user if abnormalities are detected.
3. Becoming easier to use, control, and maintain. Two growing challenges for warehouses and DCs—the need to minimize downtime in a 24-7 operation and the difficulty of hiring and retaining qualified equipment technicians—are prompting manufacturers of forklift battery chargers to take some creative steps to address those concerns. Here are three examples:
Other examples of chargers that can automatically recognize all types of lead-acid and lithium-ion batteries and charge the batteries to the proper setting include Power Designers' Revolution charger paired with its PowerTrac battery monitor and AeroVironment's ProCore chargers.
4. Revealing information that was not previously available. For users of the very small batteries in mobile devices like scanners and RFID (radio-frequency identification) readers, it's always been tough to quickly and accurately tell a "good" battery from a "bad" one. For instance, users may assume that a battery that charges quickly is a good one, but it could be charging quickly because it's older and has less capacity. As a result, they might have to change batteries during a shift or, because they think the problem is with the device itself, they might unnecessarily send the scanner or reader out for repair, says Larry Murray, CEO of Global Technology Systems Inc. (GTS), a provider of batteries and management services for mobile devices.
To address those problems, GTS developed a testing system it says can tell operators in less than five seconds whether a battery has sufficient juice for the job. The tester, about the size of a deck of cards, has two probes that touch the battery's terminal contacts. It puts a small charge into the battery, which rebounds to the tester; that information then downloads via Bluetooth to a smartphone app. A proprietary algorithm analyzes the results to determine the battery's state of health, and the app issues both visual and audible signals indicating whether the battery is "OK" or "not OK" to use. The data are also transmitted to GTS's cloud-based software for compilation and further analysis. According to Murray, this kind of aggregate data has never been available for mobile device batteries before. Once the company's database has grown sufficiently, GTS says, users will be able to compare performance among their own sites as well as against peers.
5. Getting more performance from the same size mobile device battery. When it comes to batteries for mobile devices, their small size can be both a blessing and a curse. On the one hand, they make the devices lighter and ergonomically comfortable to use. On the other hand, their size limits the amount of power they can provide over the course of a shift. Because many of today's devices incorporate more features and capabilities than their predecessors did, they tend to draw more power. For the most part, though, the size of the batteries and battery compartments haven't changed, so power may run out before the end of a shift, says Ken Murphy, COO of Impact Power Technologies, a supplier of batteries for mobile devices.
The goal, then, is to get more power and longer run times from the same size battery. Two factors will determine whether that's feasible, according to Murphy. The first is the battery's chemistry, which differs for each manufacturer. The second is the battery management system, which regulates the amount of power that goes into a battery while charging and the amount that comes out when in use. Find the perfect balance between input and output, and the battery will last much longer, Murphy explains. He and President Curt Quinter say their company has done just that, getting 20 to 25 percent more capacity into the same size battery pack and allowing the company to guarantee that its batteries will run a full shift. The combination of Japanese-made lithium-ion cells, which have the fewest impurities, together with a proprietary battery management system that prevents batteries from being overcharged or overdischarged makes that possible, they say."
Read the entire article here.